Ring complete (welding joint of this item should be leakage proof)

The nitinol core coronary wire - width should be 0.014 in diameter and length of 180 cm or more. the tip weight should be less than one gram. should have hydrophilic coating. should have 1:1 torquability. should be compatible with dock extension wire

1) breathable impervious surgical gown should be an intelligent and high-performance gowna made up of 60-gsm light weight trilaminate material. gown should provide full imperviousness to blood-borne pathogens and should meet thea standards set by aami pb70, astm f1671, and en 13795. breathable membrane should reactsa to body temperature changes, to enhance water vapor transmission for wearer comfort.a gown should be available in xl (130 cm), xll (150 cm), and 2 xll (150 cm) with raglan sleeves

Pacer with mask for child [srphc82337065-spacer with mask for children.1)it should be suitable for use for infants and children.2)the minimum capacity of the holding chamber should be approximately 250cc(ml).3)the holding chamber should have a valve to prevent rebreathing of the exhaled air.4)should be made of polymer /polycarbonated material.5)should have a mask of pediatric size suitable for covering the nose and mouth of the infant and children.6)should be compatible with the mdi which is b

Needle for inside-out meniscal repair with eye for thread.1. standard-length stainless steel with a 38cm or more in length and diameter should be 0.8 mm or less. 2. should be made up of high strength, flexible stainless steel, 3. needle should have eye on non-sharp end to pass minimum 2-0 suture. 4. needles can be used with other meniscal repair systems. (as per detailed specifications attached)

Gear oil for brm spz 350-20, brm spz 35 [gear oil for brm spz 350-20, brm spz 350-21 (under warranty machines) machines. part no.: shell omala s4 gx 220 in 209 ltr pack make- shell note- the supplied oil should be of shell make only to keep warranty intact as per oem. ]

Disposable rotatable rat tooth forceps should have 1. rat tooth / alligator jaw with opening width of 3.8 mm to 7.2 mm and compatible with 2.8 mm instrument channel. 2. firm grip & easy movould be available with rotatable graspers. 3. shaft length more than 160cm and jaw opening from 11.3mm to 14.9mm. 4.should be made of medical grade stainless steel with ptfe

Olonic metal uncovered st [srphc82336085-colonic metal uncovered stent should be made of alloy material to allow greater flexibility and use in tortuous anatomy. should have various lengths 6 or 8 or 10cm. should have a 30mm flare and 25mm body and reconstrainable even after 70 percent of deployment.] ,ontrolled radial expansio [srphc82336090-controlled radial expansion esophageal balloon dilator: 1. balloon made of pebax (polyether block amide or peba is a thermoplastic elastomer), a non-co

Procurement of lead acid cell, low maintenance, 2 volt in transparent (polypropylene)/hard rubber container conforming to irs:s-88-2004. the cells should be complete with tubular positive plates, pasted negative plates, acid level indicating floats inter-cell connector with bolts & nuts. the cells are required to be dry & uncharged. capacity of each cell will be 400/ah at 10 hrs rate to discharge to 1.85 v per cell at 27 degree centigrade.

Ortic stent graft :- shou [srphc82281040-aortic stent graft :- should enable endovascular treatment of arch of aorta and descending thoracic aorta aneurysms and dissections. the stent graft should come in various lengths and diameters. it should consist of (1) a self expanding, tubular endoprosthesis composed of a polyester graft fabric and a spring scaffold made from nitinol wire. (2) radiopaque markers are to be sewn to the fabric to radiographically visualize the edge of the graft material