Suture anchor should be made of peek material 4.75mm./ suture anchor should be made of peek material. 5.5 mm. / low profile titanium cancellous screws of diameter 4.0 mm and 6.5mm.

The nitinol core coronary wire - width should be 0.014 in diameter and length of 180 cm or more. the tip weight should be less than one gram. should have hydrophilic coating. should have 1:1 torquability. should be compatible with dock extension wire

1) breathable impervious surgical gown should be an intelligent and high-performance gowna made up of 60-gsm light weight trilaminate material. gown should provide full imperviousness to blood-borne pathogens and should meet thea standards set by aami pb70, astm f1671, and en 13795. breathable membrane should reactsa to body temperature changes, to enhance water vapor transmission for wearer comfort.a gown should be available in xl (130 cm), xll (150 cm), and 2 xll (150 cm) with raglan sleeves

Chlorine tablets for use in ir-drdo bio-toilets confirming to rcf specification mdts-14274 rev-00. technical requirements: 1. the tablet size should be 78 mm diameter and weight should be of approximately 200 g. 2. the tablet should have active molecule of 3, 5 di-chloro-isocyanuric-acid. 3. it should have effective chlorine of >= 50 percent chlorine. 4. the tablet should have formulated for sustained release (should last for at least 21 days in tap water). 5. moisture content should be

Pacer with mask for child [srphc82337065-spacer with mask for children.1)it should be suitable for use for infants and children.2)the minimum capacity of the holding chamber should be approximately 250cc(ml).3)the holding chamber should have a valve to prevent rebreathing of the exhaled air.4)should be made of polymer /polycarbonated material.5)should have a mask of pediatric size suitable for covering the nose and mouth of the infant and children.6)should be compatible with the mdi which is b

Needle for inside-out meniscal repair with eye for thread.1. standard-length stainless steel with a 38cm or more in length and diameter should be 0.8 mm or less. 2. should be made up of high strength, flexible stainless steel, 3. needle should have eye on non-sharp end to pass minimum 2-0 suture. 4. needles can be used with other meniscal repair systems. (as per detailed specifications attached)

Gear oil for brm spz 350-20, brm spz 35 [gear oil for brm spz 350-20, brm spz 350-21 (under warranty machines) machines. part no.: shell omala s4 gx 220 in 209 ltr pack make- shell note- the supplied oil should be of shell make only to keep warranty intact as per oem. ]

Drill canvas hand gloves. size-300mm. supply to be made as per corporate standard ppe specification m,hand glove mercury size 12 as per our ppe manual page no. 165-166 rev: 01 dated 30.05. 12,plastic face shield. as per bhel corporate standard: hse/ppe rev. 01, sheet no. 15 to 18.

Brazing torch,earthing clamp,welding cable 50sq.mm,welding helmet,grinding helmet face shield,leather hand gloves,leg sleeve,leather hand sleeve,spark lighter or gas lighter,hose pipe da gas,hose pipe oxygen gas,da gas regulator,oxygen gas regulator,brazing rod,welding electrode holder 600 amp,welding glass black,welding glass white,leather apron,welding goggles,cylinder key,oil stone,grinding wheel 4 inch,cutting wheel 4 inch,grinding wheel 5 inch,cutting wheel 5 inch,welding machine single phase

Disposable rotatable rat tooth forceps should have 1. rat tooth / alligator jaw with opening width of 3.8 mm to 7.2 mm and compatible with 2.8 mm instrument channel. 2. firm grip & easy movould be available with rotatable graspers. 3. shaft length more than 160cm and jaw opening from 11.3mm to 14.9mm. 4.should be made of medical grade stainless steel with ptfe