Turning tool holder as per iso key code no. scacr 2020 e 09 note-vender must give documentry evidence,plain turning tool holder similar to m/s sandvik cat. no. r171-31-2525-12 (iso identy code pclnr 2525,l. h. turning tool holder to iso identy code pclnl 2525 m-12.,bore turning tool holder(boring bar) to iso. identy code s16m-sclcr-09

Coated carbide insert for machining operation of steel to iso key code no. cnmg 120412. chip control g

Pu tube, pneumatic 10 bar at rt. as per standard 09-2012: 664 size: 6mm(od: 6mm, id: 4mm) max. opt. pr,pu tube, pneumatic 10 bar at rt. as per standard 09-2012: 664. size: 8mm. make: smc/kbl/legris/ norgen/,pu tube, pneumatic 10 bar at rt as per standard 09-2012: 664 size: 10mm. make: smc/kbl/legris/ norgen/va,pu tube, pneumatic 10 bar at rt. as per standard 09-2012: 664, size: 12mm(od: 12mm, id: 09 mm) . max. opt.,pu tube, pneumatic 10 bar at rt. as per standard 09-2012: 664 size: 16mm od, thick: 2.5mm make: smc/kb

Operating handle,complete body universal,test cup,bracket,spare gear,spare pinionsmall,spare pinion big,pinion bush brass,ratchet handle,wooden base,bevel pinion,bevel gear,guide nut,lead screw,insulation disc,thrust bearing,allen key,volume cup set of 3 abc,micro controller 80c31,electronic switch,comp. pcb,comp. meggar box,pcb display,temperature sensor,battery compartment,ic adapter 7805,connector leads 12 pin,connector leads 2 by 3 pins,relay,segment ic,timer ic 7555,switching transistor bc107,crystal 6dot144 mhz,ic 4051,ic 7447,eprom,fnd board,ic base 16 pin,ic base 28 pin,ic 7135,bell switch,45 ic base 20 pin,power supply,dc socket,ic 7600,battery cell big1dot5v 25x6,pre volt circuit set,ic 146818a,ic89t51,ic base 8 pin,carrier handle,spur pinion,max 232,pressure plate,ic74373,plunger agro,crank handle agro,top plunger,bottom plunger,circular scale,pcb low battery,pointer,buzzer,trimpot 1m,trimpot 5 k,trimpot 20k,trimpot 50k,pcb press switch,dhonosocket,thumb wheel switch,max 8031,complete pcb with prin

Calibration and repair of moisture meter,test cup,spur gear,bevel gear,guide nut,insulation disk,thrust bearing,bevel pinion,micro controller,electronic switch,com. pcb,com. meggar box,temperature sensor,i.c. regulator 7805,timer i.c. 7555,i.c 4051,i.c 7447,eprom,f.n.d. board,ic 7135,complete body universal,bracket,spur pinion bigsmall,40 pin header set,pinion brush,lead screw,volume cup a,volume cup b,volume cup c,allen key,battery compartment,adaptor,connector leads 12 pin,connector leads 2 3 pins,relay,segment i.c.,i.c. 7600,switching transistor bc 107,crystal 6.144 mhz,ic base 16 pins,ic base 28 pins,ic 7600,dry cell 1.5 nv,at mega 328 p set,lcd 16x2,duvcon mager complete sticker,22 ohm,printer i.c.,module cell for date and time,ic base 20 pin,complete power supply,scale screw,carrier handle,body universal without spare,rachet handle,max 232,pressure plate,ic 74373,spur gear axle,wooden box big small,body dmm,plunger agro,crank handle agro,top plunger,bottom plunger,circular scale,bk handle test cup,pcb l

Caliper outside 15 cm. spring,caliper inside 15 cm. spring,caliper 15 cm, hermaphrodite,divider 15 cm spring,scriber 15 cm,stud extractor ezy- out, of 8,universal scribing block 22 cm,v-block pair with clamps, 150 x 100 x 100 mm,taps and s complete set, 5, 6, 8, 10, 12 mm of 5,file feather edge 15 cm smooth,spanner 6-22 mm of 8 pcs.,interchangeable ratchet socket with a 12 mm driver,d.e. tubuler box spanner 6-25 mm of 10 with tommy bar,clamp tool maker 5 cm and 7.5 cm of 2,hand reamer set, taper pin straight flute,machine reamr parallel, helical flute 12-16 mm of 5,scraper flat 15 cm,scraper trianguler 15 cm.,scraper half round 15 cm.,chisel cold round nose 9 x 100 mm,drill chuck with key, 12 mm,pipe wrench, 400 mm,adjustable pipe die bsp cover pipe size 1 inch or 0.75 inch,wheel dresser, star-dresser with holder, length 150 mm, diamond point,wing compass 254 mm. or 300 mm.,different profile gauge, plate type for demo, metric standard,knurling tool, set of diamond,straig