Poh maintenance sub kit for no-32 tap changer consisting of 04 items: (1) intermediate gear, drg. no. a6103a / skel-4615, qty. 01 no. (2) spur gear, drg. no. a6110.1 / skel-4616, qty. 02 nos. (3) spur gear, drg. no. a6313 / skel-4617, qty. 01 no. (4) pinion, drg. no. a6401 / skel-4618, qty. 01 no.

Set of insulating rings (part of ioh/poh kit) of tap changer comprising of -- (i) insulating ring (inner) = 1 no. as per m/s. repl s part no. - s1218 or g1218 of m/s. anantashree or rdso s drg. no. - skel-4661 (alt. - 1). (ii) insulating ring (outer) = 1 no. as per m/s. repl s part no. - s1219 or g1219 of m/s. anantashree or rdso s drg. no. - skel-4661 (alt. - 1).

Set of damper for wap-5 locos as per clw specification no. clw/ms/10/005 alt.1 & clw drg.no.1210-01-215-014 alt.1. one set consists of 05 items of 24 nos: (1) axle damper as per drg.no.1210-01.215.014 alt.1 - qty: 08 nos. (2) vertical damper (secondary) as per drg no.1210-01.215.014 -alt.1 qty: 04 nos. (3) horizontal damper (secondary) as per drg no.1210-01.215.014. alt.1, qty: 04 nos. (4) yaw damper as per drg no.1210-01.215.014 alt.1 - qty: 04 nos. (5) motor damper as per drg.no.1210-01-215-

Set of sand pipe arrangement for wap-5 & wap-7 loco as per abb drg. no. ia0011-00161-bom. one set consists 07 items 36 nos. (1) sand pipe & holder 1 part no. ia0011-00165, qty. 02 nos. (2) sand pipe & holder 2 part no. 011-00166 qty. 02 nos. (3) hose part no. 016-00336, qty. 04 nos. (4) worm drive hose clip 19-28, qty. 04 nos. (5) hex hd. screw m16x40, qty. 08 nos. (6) washer, qty. 08 nos. (7) lock -nut m16, qty. 08 nos.

Set of hardware for safety bracket (j bracket) as per clw drg no. 06-1-19-108. (i) hex head bolt size m10x1.25x50,grade 8.8 with drill hole of 3.0 mm at a distance of 40 mm from head (10 mm from bottom),qty-32nos.[drg ref. 56] (ii) slotted hex nut size m10 p-8,qty-32 nos.[drg ref. 42] (iii) spring washer m10 (ty. b) ,qty-32 nos.[drg ref. 43] (iv) split cotter pin 2.5 dia x 32 lg,qty-32 nos. [drg ref. 41] (1 set consists of 04 items, 128 nos.)

Set of 04 items required to elbow connector as per clw drg. no. 1209-18.406-035, sl. no. 1, alt. 3 or latest if any for sander equipment of wag-9 locos as follows. 1) body(elbow). qty/set. = 01 no. 2) back nut. qty/set. = 01 no. 3) back ferrule. qty/set. = 01 no. 4) front ferrule. qty/set. = 01 no.

Set of special bolt for bhrr locking of tm type hs 15250a, 1)as per drg no.10t835- 015 alt-f or latest, qty-04 nos. 2)as per drg no. 10t-834-941 rev-d, qty-01 no. clw specification no-4tms.095.045, one set consist of 02 items(05 nos). (as per uvam id:2100704).

Tungsten carbide tipped tamping tool for mfi machines as per rdso specification no.tm/hm/6/320(rev-3).each set consist of following three type of tamping tool set. (1) tamping tool (type-i) drg. of tool: rdso/tm/01a/16 qty.=04nos./set(plasser part no.cu30.6840.fri) (2)tamping tool (type-ii) drg. of tool : rdso/tm/01b/16 ,qty.= 04 nos./set(plasser part no.cu30.2743.fri) (3)tamping tool (type-iii) drg. of tool : rdso/tm/15a/16 ,qty.= 08 nos./set(plasser part no.cu30.10840.fri).total tamping tool

Set of modified ballast block over spg pocket for igbt based wag-9hc locomotives. each set consisting of 04 items as mentioned:- (i) modified ballast block over spg pocket for igbt locomotive end 1 lhs, qty. 01 no., clw drg. no. 1209.02.326-332, alt-1 (ii) modified ballast block over spg pocket for igbt locomotive end 1 rhs, qty. 01 no., clw drg. no. 1209.02.326-333, alt-1 (iii) modified ballast block over spg pocket for igbt locomotive end 2 lhs, qty. 01no., clw drg. no.1209.02.326-334, alt-

Kit for jointing [btpn] consisting of 03 items. 1] gland ring for 100 mm lubricated taper plug valve to rdso drg. no. wd-93066-s-07 alt. 1, qty. - 30 nos. 2] gasket for 100 mm lubricated taper plug valve to rdso drg. no. wd-93066-s-04 alt. 1, qty. - 05 nos. 3] gland packing for 100 mm lubricated taper plug valve to rdso drg. no. wd-93066-s-08 alt. 1, qty. - 30 nos. material and specification for gland ring and gasket should be to is 2712 : 2024, gr o/2. material and specification for gl