Floor end profile,l=2000mm, as per drawing: lw41112, packing instruction: as per standard packing. it should be ensured that item should not rub during transportation.the item should be packed with adequate strength.

Wire wound resistor 4.7 ohms 1000w, size 50 mm outer dia and resistor length 380 mm with suitable fixing clamp item to be supplied along with fixing clamps. height of fixing clamp should beabove 35 mm.

Water flow meter, mechanical with calib [ water flow meter, mechanical with calibration certificate from nabl lab, is:2373 or latest, size - 50mm. least count - 10 liter, water meter should be enclosed typewith brass body cover with mettalic gears]

Trochanteric femur nail advanced system one set. spec: (1) 9 mm to 12 mm diameter with inbuilt set screw. (2) should be capable of allowing cannulated screw or blade (one) with same hole in proximal part. (3) end of blade and screw should be porous to allow augmentation with 5 mm distal locking option (two). (4) material should be titanium molybdenum. (complete range of size shape and side specific implant with instrumentation should be available at the time of surgery).[ item code no.:s6155

Needle for inside-out meniscal repair with eye for thread.1. standard-length stainless steel with a 38cm or more in length and diameter should be 0.8 mm or less. 2. should be made up of high strength, flexible stainless steel, 3. needle should have eye on non-sharp end to pass minimum 2-0 suture. 4. needles can be used with other meniscal repair systems. (as per detailed specifications attached)

Hiv (rapid/spot) test kit. spec: 1. kit should be able to simultaneously and differentially detect both antigen (hiv-1 & p-24) and antibodies for hiv on the same device. 2. kit should follow immunochromatography principle by using flowthrough or lateral flow technology. 3. kit should be able to detect seronegative hiv cases. 4. kit should detect gr o and sub type c strains of hiv, which is most prevalent in india. 5. kit should follow proper washing steps for clear interpretation of results. 6

Hose connection 3/8 x 1600 mm long to icf drg no icf/sk-3-5-517,alt-u/18 item no 2 .both end should be swivel end with three nylon washers to icf drg no icf/sk-3-5-263, alt-nil, item no 3.

1) autoclave tape roll to indicate endpoint for steam steriliser size: 19mm, 2) chemical indicator for steam sterilzation. verifies time, temperature, steam. should be convenient to use. (autoclave label) 3m cat no.comply 1250 or similar unit:strip, 3) ethylene oxide gas tape roll to indicate endpoint of eto. size 18mm/19mm x 50m paper should be of good quality & 4) cartridge containing 200 grams of 100 percent ethylene oxide gas compatible for use in eto gas sterilizer of 7,8,and 10 cubic fe

Hose connection for 3/8 x2300 mm long to icf drg no icf/sk-3-5-517, alt-u/18 ,item no- 3. both ends should be swivel end with 03 nylon washer to drg. no- icf-sk-3-5-263.

Set of end shields(de & nde) with grease [set of end shields(de & nde) with grease cups suitable to 6312/c3 bearings for m/s. i.c. electricals make oil cooling blower type ic 301m tesc, 30kw/40hp, 50hz, 415v as follows. 1) de side end shield with grease cups. qty/set. = 01 no. 2) nde side end shield with grease cups. qty/set. = 01 no. note: one sample set should be got approved before effecting bulk supply.]