Pinion puller for pulling out traction motor pinion as per attached drawing

Diode assembly as per attached drawing (assly no- var-item: 014310010000-00-35),diode assembly as per attached drawing (assly no - var-item: 014310010000-00-36)

Flange item no. 6 as per drawing no 4111110190 rev d ( mat code 241111107),guide bar item no. 12 as per drawing no 4111110190 rev d ( mat code 241111113),support plate item no. 13 as per drawing no 4111110190 rev d ( mat code 241111114)

De end shield as per drawing no 14024840040 rev 02 var 01,nde end shield as per drawing no 14024840025 rev 03 var 01,de bearing housing as per drawing no 34025542013 rev 00 item no 01,de inner bearing cap as per drawing no 34025542014 rev 01 item no 01,de outer bearing cap as per drawing no 24025542002 rev 06 item no 01,de grease flinger as per drawing no 24025542004 rev 06 item no 01,nde bearing housing as per drawing no 24025442019 rev 04 var 00,nde outer bearing cap as per drawing no 24025440010 rev 04 var 01,nde bearing assy components as per drawing no 24025442020 rev 03 var 00

Bottom rubber pad as per drawing no 3 cc 054 rev 08,side rubber ring as per drawing no 4 cc 073 rev 07,bottom rubber pad as per drawing no 3 cc 058 rev 07,side rubber ring as per drawing no 4 cc 089 rev 08,bottom rubber pad as per drawing no 4 cc 341 rev 01,side rubber ring as per drawing no 4 cc 339 rev 02,bottom rubber pad as per drawing no 3 cc 309 rev 0,side rubber ring as per drawing no 4 cc 351 rev 01

Separator to item 01 of drawing no. 32510528713 (ref. techno comm. sheet for item description),separator (top & bottom rtd) (ref. techno comm. sheet for item description),set of slot wedges to drawing no. 22710237209 rev 04 (ref. techno comm. sheet for item description),slot wedge (middle) to item 02 of drawing 32510519714 (ref. techno comm. sheet for item description)

Spanner 39x5.5x220 hw 066.01.21 fully m cd item as per specn. st08006 size no. 006 rev.01 with matl. aa10108 rev.11,screw hw 063.03.03 fully m cd item as per drg. 41203901001 rev.00 with matl. as per specn. aa7121122 rev.06,throttling screw m16x30 var.03 hw 100.04 item as per drg. 31201320009 rev.02 with matl. as per specn aa7125110 rev.07,angle hw 292.20 fully m cd item as per drg. 41204246006 rev.00 with matl. aa10108 rev.11,angle var.00 hw 292.03 fully m cd item as per drg. 31204246005 rev.00 with matl. aa10108 rev.11,angle var.01 hw 292.04 fully m cd item as per drg. 31204246005 rev.00 with matl. aa10108 rev.11,anchor plate hw 250.58 fully m cd item as per drg. 41240409016 rev.00 with matl. aa10401 rev.17,anchor plate hw 250.57 fully m cd item as per drg. 41240409015 rev.00 with matl. aa10401 rev.17,hex bolt m36 hw 063.05.02 fully m cd item as per drg. 31204018002 rev.00 with matl. aa10218 rev.07

Yoke pin for transition and non transition cbc to rdso drawing no. sk-62724, alt-32, item-12. material & specification as per drawing and conforming to rdso spec. no. wd-70-bd-10 rev.4.

Insulating base for primary helical spring of wap-5 loco as per drawing no.ia016-00274 rev 1(item is reserved for clw approved sources only) drawing no.ia016-00274 alt 1 spec:helical spring of wap-5

Vcb clamp(l clamp) of copper material as per drawing attached as annexure-ii of rdso modification sheet no; rdso/2026/el/ms/0514, rev 0, dated april 2026