Hydraulic long hose pipes,sash cord,gasket,hydraulic cylinder packings,discharge valve disc,guide bushes,bearing for agitator,gear box,impeller for agitator,oil seal for agitator shaft bearing

Certain br repair works including rehabilitation works to address cracks seepage reinforcement corrosion spalling of concrete concrete deterioration etc and repair works to roof treatment sunken treatment to toilet etc inside gtre cda dsc and ge bso

Contract for replacement of existing damaged sheets with new non-asbestos sheets of lift shaft with making an arrangement (outside and inside) from ground level to top as required for working at height in tae at rcf thal

Rear mechanical 6c drive shaft 142 060 60600,middle mechanical 6c drive shaft 142 060 60700,front mechanical 6c drive shaft 142 060 60800,suction strainer 142 040 41024,seal kit for roll back cylinder 142 020 20510 15,seal kit for boom lift cylinder 142 020 20509 14,seal kit for steering cylinder 142 050 52109,pillow block bearing 142 060 63900,spider assly 142 060 61300,drive chain 142 050 50302,driven sprocket 142 050 50303,drive sprocket 142 050 50304,vertical roll 142 050 50309,horizontal roll 142 050 50311,boom lifting cylinder 142 020 20500,bolster bush 142 050 51000,flange 142 060 60132,double tandem gear pump 142 040 41001,cable reel valve 222 060 62200,wheel stud 142 060 60145,wheel nut 142 060 60147,priority unloading manifold block 142 040 41015,steering cylinder assly 142 050 52100,hex head bolt hhb136720270,hex head bolt hhb136720290,joystick valve 4 section 274 040 41020,twin section oil cooler 308lc 050 50405,priority unloading valve 274 hpe simp 01 01,check valve for priority unloading manifol

Balance valve bush bronze mf123hpb28,disc seal seating bronze mf123hpb16,shaft sleeve sd mf123hpb05,discharge bush bronze mf123hpb29,sleeve nut en 8 mf123hpb03,gland flange bronze mf123hpb04,impeller bronze mf123hpb11b,discharge bush bronze mf123hpb29,impeller lg2 31c,guide tips ci 78072c,balance vlave pb1 70c,seating and bush with screw bblb2 71c,pair of sleeve lg2 6365c,set of 2 glands brass 26c,suction cover ci 41c,middle body ci 77c,bearing hsng set of 2 de and nde ci 22c,partition plate ci 78076,set of 2 bearing bushes lb 2 23c

Spider assly nut hn136410,spider assly bolt hn13671050,drive sprocket fixed 222 030 30400,drive sprocket 222 030 30500,idle sprocket fixed 222 030 31000,idle sprocket movable 222 030 31100,chain conveyor assembly 222 030 31700,idle shaft 222 030 31200,bush for drive sprocket motor side 222 030 30200,drive shaft 222 030 30600,seal kit for door opening cylinder 222 030 32209 14,bush for drive sprocket 222 030 30300,boom for conveyor bucket 308lc 020 20100,axle bolt 142 050 55600,sliding housing assembly 222 030 31300,bulb pilot 24 volt 142 070 70804,low pressure filter element 142 040 41120 1,shaft seal for conveyor chain motor 03020028,pilot operated dc valve for steering cylinder 274 040 41018,straight adapter 1 inch sta00100,straight adapter 3 4 inch sta003400,straight adapter 1 4 inch sta001400,straight adapter 1 2 inch sta001200,o ring 12301 060 60101,seal 123229 060 60137,piston ring 142 060 60419,gasket 142 050 53000,flp on off push button station 136 080 0009,gasket conv hsg to trans case 142 060 60307,

1 - ecentric shaft with 2 nos. key for fly wheel and 2 nos. key for labyrinth seal, drawing no. - mark no. 1-154-011,1-154-a-011 make- tega mcnally mineral limited,2 - pitman housing cover, drawing no. - mark no. 2-332-012, 2-332-a-012 make- tega mcnally mineral limited,3 - intermediate labyrinth seal, drawing no. - mark no. 1-154-007, 1-154-a-007 make- tega mcnally mineral limited,4 - fixed side bearing inside cover, drawing no. - mark no. 1-154-007, 1-154-a-007 make- tega mcnally mineral limited,5 - fixed side bearing inside cover, drawing no. - mark no. 1-154-007, 1-154-b-007 make- tega mcnally mineral limited,6 - side bearing sleeve with pin, drawing no. - mark no. 2-332-016, 2-332-a-016 make- tega mcnally mineral limited,7 - sleeve push type removal, drawing no. - mark no. 3-145-010, 3-145-a-010 make- tega mcnally mineral limited,8 - lock washer w-36 make- tega mcnally mineral limited,9 - lock nut, an-36 make- tega mcnally mineral limited,10 - fixed side bearing cover, drawing no. - mark no. 2-332-014, 2

Machining of tr shaft housings