Set of rail guard (one set consisting of following items) (1).rail guard lhs & rhs one each as clw drg. no. 03/04/62/67. (2).make up piece . qty. 04 nos. per set as per clw drg. no. 03/04/62/82. (3). bolt size 16x100 m.m. with nut, 01 plane washer & 01 spring washer . qty. 04 nos. per set. (4). bolt size 16x70 m.m. with nut, 01 plane washer & 01 spring washer. qty. 04 nos. per set. material : bolt -is : 1364/67, grade 8.8/10.9 make lps/tvs/vif/unbrako or its equivalent. spring washer is-3063/9

Set of 04 items required to elbow connector as per clw drg. no. 1209-18.406-035, sl. no. 1, alt. 2 or latest if any.

Set of special bolt for bhrr locking of tm type hs 15250a, 1)as per drg no.10t835- 015 alt-f or latest, qty-04 nos. 2)as per drg no. 10t-834-941 rev-d, qty-01 no. clw specification no-4tms.095.045, one set consist of 02 items(05 nos). (as per uvam id:2100704).

Set of damper for wap-5 locos as per clw specification no. clw/ms/10/005 alt.1 & clw drg.no.1210-01-215-014 alt.1. one set consists of 05 items of 24 nos: (1) axle damper as per drg.no.1210-01.215.014 alt.1 - qty: 08 nos. (2) vertical damper (secondary) as per drg no.1210-01.215.014 -alt.1 qty: 04 nos. (3) horizontal damper (secondary) as per drg no.1210-01.215.014. alt.1, qty: 04 nos. (4) yaw damper as per drg no.1210-01.215.014 alt.1 - qty: 04 nos. (5) motor damper as per drg.no.1210-01-215-

Jaw plate swing jaw p no dtjc 2415 03 02,jaw plate stationary jaw p no dtjc 2415 02 02,swing jaw keeper plate p no dtjc 2415 03 03,swing jaw keeper plate holding bolt p no dtjc 04 07c,stationary jaw keeper plate p no dtjc 2415 02 03,stationary jaw keeper plate holding bolt p no dtjc 2415 04 07b,pull back rod p no dtjc 2415 07 07,pull back rod spring p no dtjc 2415 07 05,rubber diaphragm p no dtjc 2415 06 03,lower wear plate p no dtjc 2415 01 07,lower wear plate holding bolt p no dtjc 2415 08 07,guard plate p no dtjc 2415 03 03,eccentric shaft p no dtjc 2415 05 01,bearing p no dtjc 2415 05 02,pitman p no dtjc 2415 04 01,front toggle p no dtjc 2415 04 02 24 12 06,rear toggle p no dtjc 2415 04 02 24 12 05,toggle pin p no dtjc 2415 04 06,toggle seat p no dtjc 2415 04 07,toggle spring p no dtjc 2415 04 04,stationary jaw holding stud for upper bl p no dtjc 2415 01 03,flywheel bush p no dtjc 2415 05 09,safety shoe p no dtjc 2415 02 03,safety arm key p no dtjc 2415 05 05a,safety flat p no dtjc 06 026,side plate p no

Lv1 r72 5365185086 bushing drg no 172-21-070,z7 rus-188.81.005 sb lever,lv1 r90 176.93.041sb hook,lv1 r90 184.04.021sb 4th lh strap,z18 r90 kit-012 19312 0407 antenna mounting kit,lv1 r72 520.01.001.01 bolt m8x1x14,lv1 r72 175.40.038 shaft throw out device,lv1 r72 gost.7798.70 bolt 3m6-6gx25.88.38xc.016,lv1 r72 172.70.112 bolt,n1 r72 5310-009923 nut m8x1 520-02-008-02,z6 r72 520-09-001-04 clamp loop,z6 r72 p6t-135 bolt fork end,z6 r72 520-01-003-08 bolt machine,c2 r72 5315049622 cotter pin 4x40.016,lv1 r72 175.02.182.1 support,lv1 r72 3040720536836 neck 175-56-009sb,lv1 r72 175.04.113.1 angle piece right hand,lv1 r72 175.02.528.1 lever,lv1 r72 172.02.175sb.1 rod,lv1 r72 520.09.001.11 clamp 14x7,lv1 r72 gost.8338.75 brg 970711 size 55x90x10mm,lv1 r72 5340430005086 4th rh shield 172-04-169sb-1,lv1 r72 175.01.057.1 cover plate,lv1 r72 172.71.130sb bracket,lv1 r72 172.42.013sb sleeve

Set of 04 items required to elbow connector as per clw drg. no. 1209-18.406-035, sl. no. 1, alt. 3 or latest if any for sander equipment of wag-9 locos as follows. 1) body(elbow). qty/set. = 01 no. 2) back nut. qty/set. = 01 no. 3) back ferrule. qty/set. = 01 no. 4) front ferrule. qty/set. = 01 no.