Valve cone (hw-065.02. 11) -- fully m/cd item as per drg. 31202624030 rev. 02 with matl. as per cbom 3,flange (hw-388.03) -- fully m/cd item as per drg. 21202457010 rev. 00 with matl. as per cbom 212024,valve cone (hw-065.01. 01) -- fully m/cd item as per drg. 31202524001 rev 00 with matl. aa19332 rev. 1,intermediate ring (hw-065.01. 07) -- fully m/cd item as per drg. 31202524007 rev 00 with matl. aa1933

Mounting plate-i (bm-011.04) as per drg. 26191003059/02 with matl as per specn. aa10119/15,mounting plate-ii (bm-011.05. a) as per drg. 26191003105/04 with matl as per specn. aa10119/15,sole plate (bm-011.03. c) as per drg. 16191002783/00 with matl as per specn. aa10119/15. rv10158197

12 pont 5 mtr high mast pole shaft in two section suitable for 50 per second wind speed as per is 875 part iii base plate 6 holes 445pcd with head frame winch mounting bracket luminaries,32 a control panel,template and anchor plate of 445 of pcd alongwith 6 nos of foundation bolts,single avaiation light fixture,2 by 2 into 4 feet concrete based pillar

1 head assembly,2 handle assembly,3 cylinder assembly,4 upper valve assembly,5 lower valve assembly,6 head-standard,7 handle standard,8 telescopic stand,9 normal stand,10 water tank,11 plunger rod,12 handle axle,13 third plate,14 connecting rod,15 socket seamless,16 bearing,17 hexagonal coupler m 12x1.75x50,18 hex. bolt m 12x1.75x40,19 hex. bolt m 12x2.0,20 hex. nut m 12x1.75,21 h.t. bolt m 10x1.75x40,22 nylock nut m 10x1.5,23 chain with coupling,24 axle washer,25 reducer cap,26 cast iron cylinder body,27 brass liner-short,28 plunger yoke body,29 plunger upper valve,30 bucket spacer,31 follower,32 check valve,33 check valve seat,34 rubber seat retainer,35 pump bucket,36 sealing ring,37 seating for upper valve,38 seating for lower valve

1 head assembly,2 handle assembly,3 cylinder assembly,4 upper valve assembly,5 lower valve assembly,6 head-standard,7 handle standard,8 telescopic stand,9 normal stand,10 water tank,11 plunger rod,12 handle axle,13 third plate,14 connecting rod,15 socket seamless,16 bearing,17 hexagonal coupler m 12x1.75x50,18 hex. bolt m 12x1.75x40,19 hex. bolt m 12x2.0,20 hex. nut m 12x1.75,21 h.t. bolt m 10x1.75x40,22 nylock nut m 10x1.5,23 chain with coupling,24 axle washer,25 reducer cap,26 cast iron cylinder body,27 brass liner-short,28 plunger yoke body,29 plunger upper valve,30 bucket spacer,31 follower,32 check valve,33 check valve seat,34 rubber seat retainer,35 pump bucket,36 sealing ring,37 seating for upper valve,38 seating for lower valve

1 head assembly,2 handle assembly,3 cylinder assembly,4 upper valve assembly,5 lower valve assembly,6 head-standard,7 handle standard,8 telescopic stand,9 normal stand,10 water tank,11 plunger rod,12 handle axle,13 third plate,14 connecting rod,15 socket seamless,16 bearing,17 hexagonal coupler m 12x1.75x50,18 hex. bolt m 12x1.75x40,19 hex. bolt m 12x2.0,20 hex. nut m 12x1.75,21 h.t. bolt m 10x1.75x40,22 nylock nut m 10x1.5,23 chain with coupling,24 axle washer,25 reducer cap,26 cast iron cylinder body,27 brass liner-short,28 plunger yoke body,29 plunger upper valve,30 bucket spacer,31 follower,32 check valve,33 check valve seat,34 rubber seat retainer,35 pump bucket,36 sealing ring,37 seating for upper valve,38 seating for lower valve

Ring oil pump,bolt m14x164,dowel pin,plug gear,o ring,bolt m14x140,isolated bolt,bolt m10x57,screw head m8x25,seal bonded,bolt flange,gasket oil cooler,tension pin,stud m8x 1 point 25,bolt inj clamp m8x29,bolt m10x120,gas strut,gasket,nut rivet,pin hose retainer,grommet,nut m5,gasket door handle,strut gas window,bearing main upper rear,bearing main lower rear,access cover,clamp injector,pipe clip,bush,door lock cover lh,resilient mount,hose,switch oil temp,seal,static nut,clamp plate,cover battery,stabilizer control rod assy,reflective tape,roller bearing,bush,seal i,liner bearing,seal ii,switch panel,switch actuator rear,switch cover,throttle hand knob,pin pivot,oil buffle plate,sealing strip,pivot pin

Site clearing setting out and levelling,earth work and foundation excavation work,pcc bellow foundation,rcc foundation pedestal,reinforcement steel,anchor bolt plates,primary steel frame,main structural steel,secondary members purlin girts bracing system,connection plates cleats bolt,roof sheeting roof thermal insulation,wall cladding wall insulation,basic drainage,structural painting coating,debris removal,rcc industrial floor and floor concrete,testing and inspection,installation and errection comisiong and handover,as built drawing,rain water downpipes,rcc industrial floor,floor concrete,floor reinforcement

Air clear element,avr plate,fuel feed pump with fuel filter assy,fuel injection pump,fuel pipe line 17x19,oil filter,piston ring set std,head gasket,fuel pump,injector nozzle,fd coil,head gasket,push rod,main bearing,blower assy,oil filter,pistion ring set,piston,push rod seal lower,push rod seal upper,rocker arm assy,fuel filter,fuel feed pump assy,air filter,push rod assy,injector assy,crank shaft thrust washer 4 piece,impeller housing assy,cr bearing set,crank shaft oil seal,sleeve std,air filter,avr plate,self starter assy,fuel pipe line tank to feed pump,fuel filter,head gasket,oil filter,pistion assy,valve oil seal,push rod,air filter,benjo nut,fuel fillter,piston,piston ring set,fuel pipe 17x19,cylinder liner,cr bearing seal 4 pieces big end seal set,main bearing 6 pieces,crank shaft seal front fly wheel side,crank shaft thrust washer 4 piece,fip return benjo bolt,air filter,fuel filter,head gasket,oil filter,injector assy,fuel filter,oil filter,common rail 3 cyl engine,fuel injection p