Co110080642: m24x140 hex. head bolt- 10.9 is: 1364 & nut-10 is: 1364 with 2 washers is: 6649 drg: dcme/,co110080640: m24x120 hex. head bolt- 10.9 is: 1364 & nut-10 is: 1364 with 2 washers is: 6649 drg: dcme,co110080641: m30x160 hex. head bolt- 10.9 is: 3757 & nut-10 is: 6623 with 2 washers is: 6649 drg: cme 84

Oil seal rubber 180 x 215 x 15 mm, sprng,bush,block plummer sn - 522,plummer block bearing block s 528,hex head bolt-2643,nut,hex head bolt - 0133,seal kit,potential transformer,new control panel assembly with up to 750ma,shaft with keys and sleeve nuts for 6 sta

1 head assembly,2 handle assembly,3 cylinder assembly,4 upper valve assembly,5 lower valve assembly,6 head-standard,7 handle standard,8 telescopic stand,9 normal stand,10 water tank,11 plunger rod,12 handle axle,13 third plate,14 connecting rod,15 socket seamless,16 bearing,17 hexagonal coupler m 12x1.75x50,18 hex. bolt m 12x1.75x40,19 hex. bolt m 12x2.0,20 hex. nut m 12x1.75,21 h.t. bolt m 10x1.75x40,22 nylock nut m 10x1.5,23 chain with coupling,24 axle washer,25 reducer cap,26 cast iron cylinder body,27 brass liner-short,28 plunger yoke body,29 plunger upper valve,30 bucket spacer,31 follower,32 check valve,33 check valve seat,34 rubber seat retainer,35 pump bucket,36 sealing ring,37 seating for upper valve,38 seating for lower valve

1 head assembly,2 handle assembly,3 cylinder assembly,4 upper valve assembly,5 lower valve assembly,6 head-standard,7 handle standard,8 telescopic stand,9 normal stand,10 water tank,11 plunger rod,12 handle axle,13 third plate,14 connecting rod,15 socket seamless,16 bearing,17 hexagonal coupler m 12x1.75x50,18 hex. bolt m 12x1.75x40,19 hex. bolt m 12x2.0,20 hex. nut m 12x1.75,21 h.t. bolt m 10x1.75x40,22 nylock nut m 10x1.5,23 chain with coupling,24 axle washer,25 reducer cap,26 cast iron cylinder body,27 brass liner-short,28 plunger yoke body,29 plunger upper valve,30 bucket spacer,31 follower,32 check valve,33 check valve seat,34 rubber seat retainer,35 pump bucket,36 sealing ring,37 seating for upper valve,38 seating for lower valve

1 head assembly,2 handle assembly,3 cylinder assembly,4 upper valve assembly,5 lower valve assembly,6 head-standard,7 handle standard,8 telescopic stand,9 normal stand,10 water tank,11 plunger rod,12 handle axle,13 third plate,14 connecting rod,15 socket seamless,16 bearing,17 hexagonal coupler m 12x1.75x50,18 hex. bolt m 12x1.75x40,19 hex. bolt m 12x2.0,20 hex. nut m 12x1.75,21 h.t. bolt m 10x1.75x40,22 nylock nut m 10x1.5,23 chain with coupling,24 axle washer,25 reducer cap,26 cast iron cylinder body,27 brass liner-short,28 plunger yoke body,29 plunger upper valve,30 bucket spacer,31 follower,32 check valve,33 check valve seat,34 rubber seat retainer,35 pump bucket,36 sealing ring,37 seating for upper valve,38 seating for lower valve

Light,hour meter,hyd oil temp gauge,ignition switch,hyd filter,bucket tooth,bucket tooth nut bolt,hand lever assy,horn,water pump gauge,fan switch,fuel gauge,hose clamp 1 inch,hose clamp 2 inches,hose clamp 3 inches,anabond,bty terminal positive,bty terminal negative,grease nipple,bolt,latch assy comp rh,latch assy comp lh,cross bar,filter air outer,filter air ,fuel filter water separator 12,engine oil filter,pump,hyd pump assy,cabin harness for skid steer,belt v,hose assembly,head leaver assembly,element hydraulic filter

Chain with flight bar assembly consisting of a chain 26x92x210 links confirming to is din 22252 or equivalent bis standard 02 nos., b flight bar 35 nos part no 317015 or equivalent,chain connector suitable for chain 26x92 02 nos. for l and t feeder breaker, part no 31705 or equivalent drawing enclosed,t head bolt for l and t feeder breaker, part no 31702 or equivalent drawing enclosed,nylock nut for l and t feeder breaker, part no 31703 or equivalent drawing enclosed,sprocket for drive shaft for l and t feeder breaker, part no 31661a or equivalent,sprocket for tail end shaft for l and t feeder breaker, part no 31641a or equivalent,sliding bearing block assembly for tail end shaft without bearing. suitable for bearing no23124cc for l and t feeder breaker, part no 31663 or equivalent,drive shaft assembly complete with sprockets, shaft, bearing, bearing block, distance piece etc. in assembled condition for l and t feeder breaker, part no 3164 or equivalent,tail shaft assembly complete with sprockets, shaft, bear

Pin dowel,diverter oil drain,plug 3 8 npt hx soc w sealant,plug hex socket 1 4 x18 sealant,scr hxfl m10x1.25x113mm 10.9,plug hex sckt w o ring m16x1.5,sump cover,plug hex sct wo ring m20x1.5,hex flange screw 6mm x35mm,screw,brkt trans joint mach,bolt m10x1.5x60mm 8.8 hexdrilock,asm cylinder 875,pin dowel m6x10,piston rings kit,pin piston,base gasket,cast water inlet cover,inlet water gasket,cylinder head gasket jp,ring rtg round 20.0x1.6,scr hxfl m6x1.0x35 10.9,scr hxfl m11x1.25x150 10.9 sem,screw,scr m6x1.0x13 sl hx fl z bleed,flat washer,oil fill tube assembly,o ring 12mm x 2mm,dipstick assembly,oil to water cooler,filter adaptor straight,10 micron oil filter,filter hd oil,cover breather,bracket tube oil fill lower,o ring 612x818x103,cover breather seal,scr sh m6x1.0x16 8.8 zpy d204,seal filter adapter 3hole,adapter oil filter mach,scr hxsoc m8x25 zpc,spherical exhaust spring,stub spherical exhaust,mnt isolator,spring exhaust s s shotpeened,double spherical gasket 2 in,heater oxygen sensor,screw,scr hxfl m6

For complete deion and other details, please refer to tender

For complete deion and other details, please refer to tender