Set of white pvc sink waste coupling size 1.5 inch dia threaded bottom portion and 2.5 inches dia of top s.s. jali, with pvc reducer heavy duty dia size 1.5 inch x 1.0 inch dia for coach wash basins. specification / drawing reference: material spec.: pvc (polyvinyl chloride) spec:

Gm wheel valve 3 bata 4 inch,gm wheel valve 1 bata 2 inch,ci right angle valve 4 inch for door,gm wheel valve 1 inch,gm wheel valve 10mm,ss gate valve 1 inch,gm nrv3 bata4 inch,gm wheel right angle v bata v both side thread size 3 bata 4 inch diameter 15mm,oxygen regulator,lpg regulator,neoprene rubber joint sheet size 1 bata 4 inch,neoprene rubber strip for juice heater 16mm x 20mm,asbestos rope 1 inch,asbestos rope 5 bata 8 inch,asbestos rope 3 bata 4 inch,rubber cone for gauge glass size 3 bata 4 inch,guage class 3 bata 4 inch x 22 inch,coupling tyre px 45,coupling tyre px 50,coupling tyre px70,coupling tyre px80,tyre coupling complete set px 70,tyre coupling complete set px 60,tyre coupling set px45,tyre coupling set px50,ms round bar 3 bata 4 inch dia,ms flate bar size thickness 3mm width 1 inch,en 8 shaft 5 inch dia,ms flat iron 50mm x8mm thickness,ms bolt 3 bata 8 inch x 3 bata 4 inch long,split pin for rbc 1 bata 4 inch x 2 inch,split pin for rbc 3 bata 16 inch x 2 inch,split pin for cane unloader 3 b

Sink or wash basin ceramic,urinal pot with all fitment items,wc indian type and p trap and foot rest complete set,upvc pipe 0 point 5 inch 6 mtr long,pvc pipe 0 point 75 inch 6 mtr long,pvc pipec 110 mm dia 6 mtr long,door latches,pvc elbow,pvc coupler,pump 1 hp,end cap,ball valve 25 mm,tank connector,pipe nipple,brass nipple,waste coupling,pvc pipe 4 inch dia,rubber washer,water tap 1 inch,jet spray,stop cock 1 or 2 inch dia isi mark,glue,teflon tape,pvr machine,alkathene pipe 2 inch dia,bib cock 1 or 2 inch dia,ppr stop cock 1 inch dia,ppr stop cock 1 or 2 inch dia,gi pipe 3 or 4 inch dia 6 mtr long isi mark,gi pipe 1 inch dia 6 mtr long isi mark,gate valve 1 inch dia isi mark,gate valve 3 or 4 inch dia isi mark,gi tee 3 or 4 inch dia isi mark,gi elbow 1 inch dia isi mark,gi elbow 3 or 4 inch dia isi mark,gi couplings 3 or 4 inch dia isi mark,gi couplings 1 or 2 inch dia isi mark,waste pipe for wash basin,gi pipe 15 mm length of 6 m as per isi specification,ppr pipe clamping machine,ppr pipe 1 inch dia,ppr

Composite multi layer pipe of size dia 25mm and outer dia 32mm as per tech spec,gi pipe 100mm dia 3m long confirming to conforming to is 1239 as per tch spec,gi tank nipple 25mm 6 inch with check nut and washer complete as per tech spec,ppr elbow 32mm conforming to is 15801 as per tech spec,ppr socket 32mm confirming to is as per tech spec,ppr equal union dia 25mm and outer dia 32mm complete as per tech spec,pp-r end cap 32mm dia suitable for 32mm outer dia pipe as per tech spec,pp-r connector 32mm dia suitable for 32 or 25mm outer dia pipe as per tech spec,pp-r tee 32mm dia suitable for 32mm outer dia pipe as per tech spec,pp-r reducer 32mm dia suitable for 32mm outer dia pipe as per tech spec,gi nipple 25mm 3 inch long as per tech spec,m seal 100 gm each pkt complete,cotton thread 100m long complete.,bib cock brass 15mm as per tech spec,gi nipple 25mm 4 inch long as per tech spec,gi nipple 25mm 6 inch long as per tech spec,gi equal union dia 25mm and outer dia 32mm as per tech spec,gi tee

R32 button bit comma 51 mm r32 part no. 7733 dash 5251a dash s48,extension rod for r32 drill rod part no. 7853-3331-30,shank adopter for r32 drill rod part no. 7803-7672-01,coupling sleeve r32 part no. 7993 dash 3644 dash s48,tct drill rod 22mm bracket 7 oblique 8 inch chisel bit integral rod hex 22 comma shank hex 22 mmx108mm comma length 3200 mm comma bit dia 31 mm part no. 714 dash 3231,tct drill rod 22mm bracket 7 oblique 8 inch chisel bit integral rod hex 22 comma shank hex 22 mmx108mm comma length 3600 mm comma bit dia 31 mm,pneumatic jack hammer type rh 658 5l,lubricator coupling,pneumatic pusher leg bmt51,male female coupling,heavy duty pneumatic rubber aire hose 20 mm for 10.2 kg per cm2 pressure conforming to is 911 dash 1968 is 446 1980,air hose clamp 20 mm dia with nut and bolt

R32 button bit comma 51 mm r32 part no. 7733 dash 5251a dash s48,extension rod for r32 drill rod part no. 7853-3331-30,shank adopter for r32 drill rod part no. 7803-7672-01,coupling sleeve r32 part no. 7993 dash 3644 dash s48,tct drill rod 22mm bracket 7 oblique 8 inch chisel bit integral rod hex 22 comma shank hex 22 mmx108mm comma length 3200 mm comma bit dia 31 mm part no. 714 dash 3231,tct drill rod 22mm bracket 7 oblique 8 inch chisel bit integral rod hex 22 comma shank hex 22 mmx108mm comma length 3600 mm comma bit dia 31 mm,pneumatic jack hammer type rh 658 5l,lubricator coupling,pneumatic pusher leg bmt51,male female coupling,heavy duty pneumatic rubber aire hose 20 mm for 10.2 kg per cm2 pressure conforming to is 911 dash 1968 is 446 1980,air hose clamp 20 mm dia with nut and bolt

Half inch drive, cordless impact wr [half inch drive, cordless impact wrench (lithium-ion technology), with deep impact sockets (socket 10mm, 11mm, 13mm,17mm, 19mm, 22mm, 24mm each one) technical specification : voltage: 18v, torque max: 180 nm, no load speed: 0- 2800 rpm, rated impact rate: 03-200 bpm, screw dia: m6-m16, tool holder: 1/2 inch external square, weight inclusive battery 1.7 kg. approx. make and model : bosch, model no. gds 18v, li (or) makita, dtw 190 jx1 (or) dewalt (or) groz m

Air compressor for plasma cutting machine,angle plate adjustable 250 x 150 x 175,anvil 24 sq. inches working area with stand,bearing different types,boring bar indexable,caliper hermachrodite.spring 15 cm,caliper inside spring 6 inch or 15 cm,caliper outside spring 6 inch or 15 cm,caps screws m6, m8, m10, m12,carbide wear block 1 mm-2 mm.,carrier for mounting components,,drill twist 1.5 mm to 15 mm,drills guage straight shank,drills guage straight shank,cut section models for hydraulic components,cut section models for penumatic components,divider spring 6 inch or 15 cm,dowel pin straight dia. 1 inch length 4 inch,drift drill 200 mm hardened and black finish,stake grooving. 100 x 100 x 300 mm,stake hatchet with leg. 300 x 200 x 20 mm,file knife edge smooth.15o mm,file round 2nd cut 150 mm,file round 2nd cut 200 mm,file square 2nd cut 250 mm,file square rough 300 mm,file triangular 2nd cut 200 mm,marking out table 90 x 60 x 90 cm,drill gauge 1,5 to 12.5 mm in steps of 0,5 mm,drill twist st. shank metric,drill

Plywood for general purposes marked to is 303 (v3),plywood for general purposes marked to is 303 (v3),plywood for general purposes marked to is 303 (v3),wash basins - vitreous sanitary appliances (vitreous china) conforming to is 2556 (part 4),(vitreous china) - washdown water closets as per is 2556,cp brass waste coupling 40 mm,gi nipple 20 mm x 100 mm,fevicol 1 kg in pack,cast brass float valve 15 mm with ball and rod complete,cast brass valves plunger type 20 mm,ewc single piece vitreous china ware complete,mild steel sliding door bolt cllpt type 300 mm long, rod not less than 16mm dia, isi marked,paint synthetic enamel smoke gray first quality in 04 ltr container,gi tee 25 mm,stainless steel butt hinges size 75 mm,ptmt waste coupling 32 mm,gi socket 15 mm,cp brass extention nipple for 15mm bore 65mm long,cast brass gate valve, with iron wheel head screwed both ends and for iron pipes and fixed for bore of pipe 25 mm,ss plate rack 24 inch x24 inch x10 inch,synthetic enamel paint of black colour.,polish fre

Plywood for general purposes marked to is 303 (v3),plywood for general purposes marked to is 303 (v3),plywood for general purposes marked to is 303 (v3),wash basins - vitreous sanitary appliances (vitreous china) conforming to is 2556 (part 4),(vitreous china) - washdown water closets as per is 2556,cp brass waste coupling 40 mm,gi nipple 20 mm x 100 mm,fevicol 1 kg in pack,cast brass float valve 15 mm with ball and rod complete,cast brass valves plunger type 20 mm,ewc single piece vitreous china ware complete,mild steel sliding door bolt cllpt type 300 mm long, rod not less than 16mm dia, isi marked,paint synthetic enamel smoke gray first quality in 04 ltr container,gi tee 25 mm,stainless steel butt hinges size 75 mm,ptmt waste coupling 32 mm,gi socket 15 mm,cp brass extention nipple for 15mm bore 65mm long,cast brass gate valve, with iron wheel head screwed both ends and for iron pipes and fixed for bore of pipe 25 mm,ss plate rack 24 inch x24 inch x10 inch,synthetic enamel paint of black colour.,polish fre