Rf synthesized signal generator 10 khz to 28 ghz, make: keysight/r&s

40 ghz cable for anechoic chamber

Programmable dc power source: p. n: n5746a with rackmount kit: p/n: n5740a: make: m/s. keysight,usb-gpib controller: p. n: 82357b: make: keysight,gpib extender cables: p. n: 10833b: make: keysight,data acquisation unit p/n: 34980a with rackmount kit: p/n: y1130b: make: keysight,32 channel gp relay: p/n: 34937a: make: keysight,32 channel gp relay terminal block: p/n: 34937t: make: keysight,40 channel mux: p/n: 34921a: make: keysight,40 channel mux terminal block: p/n: 34921t: make: keysight

Advanced memory extraction system,protocol analysis toolkit,ai enabled drone forensics analysis suite,high performance ai workstation,full duplex software defined radio 70 mhz to 6 ghz,handheld spectrum analyzer upto 6 ghz,wideband antenna set 70 mhz to 6 ghz,broadband low noise amplifier 70 mhz to 6 ghz,engineering grade multi-functional 3d printer,power amplifier,3 dof uav stability test platform

Calibration services - pressure gauge, general or baumer or wika as per sor sl no1 schedule of rates under section vii of atc as per attached atc document as per attached atc document as per attached atc document,calibration services - temperature gauge, general or baumer or wika, capillary tube sensor 0 to 100 deg c as per sor sl no2 schedule of rates under section vii of atc as per attached atc document as per attached atc document as per attached atc do..,calibration services - temperature gauge, general or baumer or wika, capillary tube sensor 50 to 200 deg c as per sor sl no3 schedule of rates under section vii of atc as per attached atc document as per attached atc document as per attached atc d..,calibration services - pressure gauge, general or baumer or wika 0 to 40 kg per cm2 as per sor sl no 4 schedule of rates under section vii of atc as per attached atc document as per attached atc document as per attached atc document,calibration services - pressure gauge, general or baumer or wika 0

Calibration services - safety relief valve as per as per sor sl no1 schedule of rates under section vii of atc as per approved atc document as per approved atc document as per approved atc document,calibration services - pressure safety valve as per sor sl no 2 schedule of rates under section vii of atc as per approved atc document as per approved atc document as per approved atc document,calibration services - pressure safety valve, leser, (set pressure 40 kg per cm2) as per sor sl no 3 schedule of rates under section vii of atc as per approved atc document as per approved atc document as per approved atc document,calibration services - creep relief valve as per sor sl no 4 schedule of rates under section vii of atc as per approved atc document as per approved atc document as per approved atc document,calibration services - creep relief valve (set pressure 23 kg per cm2) as per sor sl no 5 schedule of rates under section vii of atc as per approved atc document as per approved atc document as

Mark iv carbon fiber frame,bonka 22 point 2v 5200 mah 35c 6s lithium bty,i max eco 2807 1300kv bls motors,propellers,stack micoair,geprc mataen vtx pro,foxeer pagoda pro omini fpv antenna,radio master rp3 elrs receiver,radio master gx12,micoair m10 gps ultra,camera run cam phoeonix 2,capacitor 35v 1000 micro fared,dc buck converter,li ion,goggles sky zone sky 40 pro,xt 60 connector,bty anti slip pad,antennas,foxeer pagoda pro 5 point 7 ghz

Calibration and repair of moisture meter,test cup,spur gear,bevel gear,guide nut,insulation disk,thrust bearing,bevel pinion,micro controller,electronic switch,com. pcb,com. meggar box,temperature sensor,i.c. regulator 7805,timer i.c. 7555,i.c 4051,i.c 7447,eprom,f.n.d. board,ic 7135,complete body universal,bracket,spur pinion bigsmall,40 pin header set,pinion brush,lead screw,volume cup a,volume cup b,volume cup c,allen key,battery compartment,adaptor,connector leads 12 pin,connector leads 2 3 pins,relay,segment i.c.,i.c. 7600,switching transistor bc 107,crystal 6.144 mhz,ic base 16 pins,ic base 28 pins,ic 7600,dry cell 1.5 nv,at mega 328 p set,lcd 16x2,duvcon mager complete sticker,22 ohm,printer i.c.,module cell for date and time,ic base 20 pin,complete power supply,scale screw,carrier handle,body universal without spare,rachet handle,max 232,pressure plate,ic 74373,spur gear axle,wooden box big small,body dmm,plunger agro,crank handle agro,top plunger,bottom plunger,circular scale,bk handle test cup,pcb l

Angle gauge for tool grinding standard,anvil 50 kg - with stand,blow lamp 1 liter capacity,bunsen burners,digital lux meter lcd read out 0.05 to 7000 lumens with battery.,drill angle gauge 45 degree,60 degree,90 degree,dual dc regulated power supply 30-0-30 v, 2 amps,earth copper plate 60cm x 60cm x 3.15 mm,hot wire ammeter 0-15 amps.,lcr meter digital handheld,lead acid battery- 12v 100 ah,lead acid battery- 12v 40 ah,lead acid battery- 12v 75 ah,magnetic flux meter 0-500 tesla,magnifying glass 75 mm with magnifying factor 10x,manual motor coil winding machine,pipe vice cast iron with hardened jaw open type 100 mm,precision angle grinding vice 200 mm,rheostat 0-25 ohms 1 amp,rheostat 0-300 ohms 2 amp,side and face cutter dia 80 x 10 x dia 27 mm,slitting saw cutter dia 75 x 4 x dia 27 mm,soldering and de soldering station,stands with clamps for burette,sterilizer,sun shine recorder,taps and s complete 5, 6, 8, 10 and 12mm of 5,temperature controlled soldering iron 50 watt, 230 volt,temperature gaug