Procurement of support roller with shaft in assembled condition for roaster / calciner

Seal bar along with two no. keys and four m4 screws in assembled condition, moc: sg-cast iron confir

Supply of assembled al alloy brow 5 m as per bom of dwg no 1634 11 rev 02 along with loose condition material for y16501,supply of assembled al alloy brow 3 m as per bom of dwg no 1634 13 rev 02 along with loose condition material for y16501,supply of assembled al alloy brow 5 m as per bom of dwg no 1634 11 rev 02 along with loose condition material for y16502,supply of assembled al alloy brow 3 m as per bom of dwg no 1634 13 rev 02 along with loose condition material for y16502,supply of assembled al alloy brow 5 m as per bom of dwg no 1634 11 rev 02 along with loose condition material for y16503,supply of assembled al alloy brow 3 m as per bom of dwg no 1634 13 rev 02 along with loose condition material for y16503,supply of assembled al alloy brow 5 m as per bom of dwg no 1634 11 rev 02 along with loose condition material for y16504,supply of assembled al alloy brow 3 m as per bom of dwg no 1634 13 rev 02 along with loose condition material for y16504,supply of assembled al alloy brow 5 m as per bom of dwg

Rotex standard coupling sets in unbored condition along with spider as per technical specification,spare rotex 48 spider of 98 shore hardness a size gr 48 as per attached specification

External transfer drawer system along with shielded cubicles as per technical specification

Enhanced capacity screw coupling assembly for coaching stock, to drawing/ specification rdso spec. c-9505 [revised -aug 2001], rdso/sk- 99001, alt. no. 4, item no.-1 to 17 in assembled condition.

Vestibule locking pin internal, item no. 1 & 2 in assembled condition as per rcf drg. no. lw56359 alt nil or latest. (note: length of item no. 2 (chain) should be 20 inches or more. material and specification as per drawing)

Chain with flight bar assembly consisting of a chain 26x92x210 links confirming to is din 22252 or equivalent bis standard 02 nos., b flight bar 35 nos part no 317015 or equivalent,chain connector suitable for chain 26x92 02 nos. for l and t feeder breaker, part no 31705 or equivalent drawing enclosed,t head bolt for l and t feeder breaker, part no 31702 or equivalent drawing enclosed,nylock nut for l and t feeder breaker, part no 31703 or equivalent drawing enclosed,sprocket for drive shaft for l and t feeder breaker, part no 31661a or equivalent,sprocket for tail end shaft for l and t feeder breaker, part no 31641a or equivalent,sliding bearing block assembly for tail end shaft without bearing. suitable for bearing no23124cc for l and t feeder breaker, part no 31663 or equivalent,drive shaft assembly complete with sprockets, shaft, bearing, bearing block, distance piece etc. in assembled condition for l and t feeder breaker, part no 3164 or equivalent,tail shaft assembly complete with sprockets, shaft, bear

Body side stanchion short (length-650mm) for boxnhl wagon (outer hole distance of 118 mm from center). drawing no. : ser s drg. no. : kgp-2870, item no. 1 to 4 are in assembled condition, and item no. 5 in loose condition. material and specification : as per drawing and conforming to rdso s spec. no. wd-01- crf-12 (rev.1) of january 2016.

Supply, installation and commissioning of electric motor driven screw type air compressor vfd based cap. 250 cfm along with air receiver and air dryer as per detailed technical specification attached.