Turn buckle with hex nut (m-24), pull rod (dia 25 x 1255) mm and pull rod (dia 25 x 740) mm, all items are in assembled condition.

Clutch plate,pressure plate,clutch bearing,siren,4x4 gear bearing set,matting set,siren,black film,vip bar light led,flag rod,pen drive,speakers,music player,water pump assembly,fan belt,enjector rear,wheel cylinder,disk rooter,uj cross,head lamp,diesel filter assembly,air filter,thermostat assembly,wiper blade,axel bearing,link rod,balance rod clip bush,break shoes,wheel bearing,load rod braket,door lock,wheel bearing,break shoes,disk rooter,disk pad,break pipe,diesel filter assembly

Set of connecting rod small end needle roller bearing. each set consist of the following: (i) auxiliary connecting rod small end needle roller bearing rna 6902 (20x28x23) as per elgi part no. 000903711 of trc 1000mn compressor or similar,

Supply of double part endless wire rope sling as per specification attached,supply of sling with both end reeving, 6 x 37 fibre core construction as per specification attached,hp turbine turn buckle of min. 10 tonnes swl with both ends fork for turbine hp rotor as per specf,lp turbine turn buckle of min. 40 tonnes swl with both ends fork for turbine lp rotor as per specf

Needle roller bearing part no mh905707300,intermediate link part no mh18960,thrust bearing part no mh905708300,oil seal gd-dia50xdia62x5thk part no mh907799100,taper roller bearing part no mh906197100,taper roller bearing part no mh905147300,oil seal gd-dia100 x dia125 x 13thk part no mh958507920,washer bearing lock part no mh906085100,seal kit steer cylinder part no 12292,unloader valve assy part no mh797405113,brake valve assy part no mh797405113,spring br chember assy lh part no mh797405153,spring br chember assy rh part no mh797405163,control valve cable part no mh798906012cbl,3 8inch id hose assembly-3 4inch16unf end fitting l-1700 with drop elbow part no mh795107199,hose assembly 1-5 16inch unf end fitting l-1100 part no 795107179,tube hoist assembly rh part no mh798906093,hose assembly 1-5 16inch unf end fitting l 750 part no mh795207179,tube hoist lh part no mh798906083,pump part no mh797407022,pump gasket part no mh797408124,hose part no mh993824103,filter element part no mh8000102912,rod end part no

Oil filter,fuel filter,fuel pipe line,front brake pad,block,piston ring,piston with pin,connection rod assy,oil seal,head gaskit,packing seal,bearing,mian bush set,big end brg set,chock cable,carboator assy,oil filter,oil filter,fuel filter,fuel filter,connection rod assy

Cs010270013-variable speed fluid coupling. make -premium. size - 20 scr 25b.,st010390029-multi disc unit for 20scr fluid coupling,sc110160215-shaft,sc110160216-input shaft,sc110160217-scoop housing and scoop tube assembly,sc110160218-bearing liner bracket,sc110160219-bearing liner- impeller,sc110160220-end cover p.b. front,sc110160221-bearing liner -pillow block,sc110160222-operating lever,sc110160223-end cover,sc110160224-scoop housing shroud,sc110160225-woodruff key,sc110160214-vent tube,sc110160213-end cover rear,sc110160212-feed tube,sc110160211-bearing nut,sc110160210-control lever,sc110160209-bearing cover,sc110160208-oil retaining ring,sc110160207-collector ring,sc110160206-connecting tube,sc110160205-operating rod,co030060227-set of circlip for 20scr 25b fluid coupling. one - one fluid coupling requirement.,co030060228-set of joints for 20scr 25b fluid coupling.one - one fluid coupling requirement.,co030060226-v ring,co030060225-bonded seal,co030060229-set of special fasteners for 20 scr 25b.

End frame driving end assembly (machined) with air outlet net for traction motor ( type 6fra6068) of wap-7/wag-9 loco as per clw drg. no. 1twd.096.005/alt-11 (ref 4) and clw specification no 4tms.0960.068 rev. 2 alt 2 (abb documents no. 3ehm 112008). manufacturers shall machine the bore of bearing housing of end frame for a dimension near 319.970 mm to achieve interference over the complete range of tolerence of od of outer racer. note : required range of bearing housing of end frame - 319.9

Lv2 icvs 3020720100944 765-47-61 rack,lv2 icvs 4720-001357 765-84-sb182 hose assembly, metal,lv2 icvs 4510720158316 765-38-259 stopper,waste drain,lv2 icvs 5307720212457 700-29-459 stud plain,lv2 icvs 5340-015084 765-17-605 tie rod tensioning threaded end,lv2 icvs 4910003252 765-24-sb218 rod,lv2 icvs 9905001266 765-05-sb595 plate instruction

Chain with flight bar assembly consisting of a chain 26x92x210 links confirming to is din 22252 or equivalent bis standard 02 nos., b flight bar 35 nos part no 317015 or equivalent,chain connector suitable for chain 26x92 02 nos. for l and t feeder breaker, part no 31705 or equivalent drawing enclosed,t head bolt for l and t feeder breaker, part no 31702 or equivalent drawing enclosed,nylock nut for l and t feeder breaker, part no 31703 or equivalent drawing enclosed,sprocket for drive shaft for l and t feeder breaker, part no 31661a or equivalent,sprocket for tail end shaft for l and t feeder breaker, part no 31641a or equivalent,sliding bearing block assembly for tail end shaft without bearing. suitable for bearing no23124cc for l and t feeder breaker, part no 31663 or equivalent,drive shaft assembly complete with sprockets, shaft, bearing, bearing block, distance piece etc. in assembled condition for l and t feeder breaker, part no 3164 or equivalent,tail shaft assembly complete with sprockets, shaft, bear