Similar Tenders

• Flange for fixing shock absorber....

  Ministry of Railways Closes 16/11/2026

  View tender →

• Flange for fixing shock absorber (modified) to icf drg. no. t-0-5-662, alt. f/5, item no. 1 (mat. & spec. as per drg.)

  Ministry of Railways Closes 30/11/2026

  View tender →

• Torque wrench, adjustable ratchet type w [torque wrench, adjustable ratchet type with coupler, 1/2 inch square drive, range:- (70-340) nm. make/brand:- norbar/gedore/ stahlwille/snap on or similar ]

  Ministry of Railways Closes 30/10/2026

  View tender →

• Four bolt square flange housing bearing unit no. f-212 ,make ntn,fag or similar for airless centrifugal shot blasting machine ,make surface international

  Ministry of Railways Closes 23/10/2026

  View tender →

• Linear drive module msl 1-120 with complete assembly including 02 nos shock absorbers msl-s1-1 & 02,linear drive module msl 1-120 with complete assembly including 02 nos shock absorbers msl-s1-1 & 02,angular gripper including tongue model-msg-z1-18- degree, having part no. 33600016.1180 of heinz maye

  Munitions India Limited | Department of Defence Production Closes 31/10/2026

  View tender →

• Cordless impact wrench with following technical specifications: 1) battery voltage: 18volts dc; 2) battery capacity & type: 4ah li-ion battery, 3) max. torque: 225n-m, 4) max. speed: 1900rpm, 5) tool holder: 1/2 inch external square 6) similar to: model dtw300 of makita. make: makita/bosch/hitachi note: item to be supplied with 2nos. of battery along with charger unit.

  Ministry of Railways Closes 23/10/2026

  View tender →

• Stln part no 5930 72 0488954 demistar switch,stln par no b5a03303 double check valve,stln part no x3534115 bush bolt mounting bracket,stln part no f4650510 mounting bracket hanger,stln part no f2739200 oil seal transfer case rear,stln part no 2540 72 0000645 struct assembly cabin shock absorber,stln part no 7446400 door lock rh,stln part no b1301403 clutch plate 2012 model,stln part no x1605822 fly wheel assembly 2008 model,stln x3988100 starter motor assy double pole 9 teeth pinion with out spring,stln part no 2520 72 0000522 clutch master cylinder tvs,stln part no f7474000 air compressor single cylinder,stln part no 5930 72 0466969 2 pole isolate switch,stln part no p5400532 flange yoke 8 hole nut

  Indian Army | Department of Military Affairs Closes 23/10/2026

  View tender →

• Adjustable spanner,angle plate adjustable,angle plate size,anvil,bearing different types,belt tensioner gauge,bldc motor with controller 200 w,bolt and nut with washer,caps screws,carrier for mounting components,cast iron globe valve,combination set,cross pain hammer,cross pane hammer,damaged old spur gear,different type of engine bearing model,file swiss type needle,forge with hand blower,fuel injection pump ve pump,hand reamers adjustable,injector,injector,pipe cutting tool,pipe flaring tool,piston ring,plastic welding machine,radiator pressure cap,slip on forged steel flange,suitable gas cutting table,swaging and flooring tool kit,thread pitch gauge metric,turbocharger,universal scribing block,v-belt and flat belt,washe clutch andotheraccesorries,water pump,wire cutter for mig welding

  Directorate of Employment & Training | Labour and Employment Department Gujarat Closes 27/10/2026

  View tender →

• 1/2 inch torque wrench 60-340n-m with 3 percent high accuracy with aluminum alloy handle with anodic treatment & cr-mo square drive with 48 gear teeth, dual way direction (c.w./c.c.w.) click type, quick release button, adjusting & aluminum ring locking system of makes: stmt 73591-1-8 of stanley or its equivalent model of kingtony or snapon. note: 1) calibration certificate to be supplied along with material. 2) authorised dealership certificate to be supplied during tender.

  Ministry of Railways Closes 05/11/2026

  View tender →

• Air compressor for plasma cutting machine,angle plate adjustable 250 x 150 x 175,anvil 24 sq. inches working area with stand,bearing different types,boring bar indexable,caliper hermachrodite.spring 15 cm,caliper inside spring 6 inch or 15 cm,caliper outside spring 6 inch or 15 cm,caps screws m6, m8, m10, m12,carbide wear block 1 mm-2 mm.,carrier for mounting components,,drill twist 1.5 mm to 15 mm,drills guage straight shank,drills guage straight shank,cut section models for hydraulic components,cut section models for penumatic components,divider spring 6 inch or 15 cm,dowel pin straight dia. 1 inch length 4 inch,drift drill 200 mm hardened and black finish,stake grooving. 100 x 100 x 300 mm,stake hatchet with leg. 300 x 200 x 20 mm,file knife edge smooth.15o mm,file round 2nd cut 150 mm,file round 2nd cut 200 mm,file square 2nd cut 250 mm,file square rough 300 mm,file triangular 2nd cut 200 mm,marking out table 90 x 60 x 90 cm,drill gauge 1,5 to 12.5 mm in steps of 0,5 mm,drill twist st. shank metric,drill

  Directorate of Employment & Training | Labour and Employment Department Gujarat Closes 29/10/2026

  View tender →