P6a1z44980-face grooving tool holder and grooving inserts of m/s taegutec

Supply of tee equal 15mm (nominal size of outlet) & minimum length, centre to face: 32 mm as per specification attached.

Carbide drill dia 6 mm type 2010-6.00 make: -ifanger/applitec/bimu or equivalent.,boring tool type 440100-r-k10 make: - ifanger/applitec/ bimu or equivalent.,boring tool type mten 425060-r-k10, tool will be used for finish boring, length of finish boring 3.9,boring tool type mten 425100 r-k10, tool will be used for finish boring, length of boring 8.00 mm, n,multi function tool holder dr-mf-16r 2.25 d: 01 no. insert xcmt 080304-mf-ic908: 50 nos. screw so 30,90 degree eco cut multifunction tool, over all length 94 mm, shank dia 20mm. ecc 16r-2.25 d08 - qty:

Tungsten carbide tipped tamping tool for mfi machines as per rdso specification no.tm/hm/6/320(rev-3).each set consist of following three type of tamping tool set. (1) tamping tool (type-i) drg. of tool: rdso/tm/01a/16 qty.=04nos./set(plasser part no.cu30.6840.fri) (2)tamping tool (type-ii) drg. of tool : rdso/tm/01b/16 ,qty.= 04 nos./set(plasser part no.cu30.2743.fri) (3)tamping tool (type-iii) drg. of tool : rdso/tm/15a/16 ,qty.= 08 nos./set(plasser part no.cu30.10840.fri).total tamping tool

Set of tungsten carbide tamping tools (tctt) for csm/duomatic (old model) as per rdso technical specification no: tm/hm/6/320 (rev-3). each set consist of following four type of tamping tool set. 1) tamping tool (type-i) drg. of tool: rdso/tm/l4a/l6 qty.=16nos/set. 2) tamping tool (type-ii) drg of tool : rdso/tm/14b/l6, qty.= 4 nos./set. 3) tamping tool (type-iii) drg of tool : rdso/tm/14c/i6, qty.= 4 nos./set). 4) tamping tool (type-iv), drg of tool : rdso/tm/l4d/l6, qty.= 8 nos./set. total t

Triple-lumen central venous cannula/catheter set. specification - 1) material: radio opaque biocompatible polyurethane. 2) number of lumen: 3 (three). 3) size: 7f. 4) length of catheter: 16-20 cm. 5) the complete sterile set must contain the following - a) valve needle. b) luer lock syringe 5 ml. c) kink proof guidewire of compatible size and length made of nickel-titanium. d) triple lumen 16g-18g-18g radiopaque-biocompatible-polyurethane made, 7f outer diameter, soft tip, with valves. length

Cordless impact wrench with following technical specifications: 1) battery voltage: 18volts dc; 2) battery capacity & type: 4ah li-ion battery, 3) max. torque: 225n-m, 4) max. speed: 1900rpm, 5) tool holder: 1/2 inch external square 6) similar to: model dtw300 of makita. make: makita/bosch/hitachi note: item to be supplied with 2nos. of battery along with charger unit.

Cordless impact wrench with following technical specifications: 1) battery voltage: 18volts dc; 2) battery capacity & type: 4ah li-ion battery, 3) max. torque: 225n-m, 4) max. speed: 1900rpm, 5) tool holder: 1/2 inch external square 6) similar to: model dtw300 of makita. make: makita/bosch/hitachi or equivalent. note: item to be supplied with 2nos. of battery along with charger unit.

Pneumatic rivet gun,chain puller block,caliper hermachrodite,card file steel wire brush,profile gauges,boring bar,dowel pin,standard tap screws,medium carbon heat treated alloy steel metric studs and bolts along with nuts for display of standard length,caps screws,drills guage straight shank,drills guage straight shank,drill gauge,bolt nut and washer set,gear spur,belt v,belt flat,washer clutch keys jib cotter and circlip,lifting sling,swage block 5048,set of rowel punch,conduit pipe cutting and threading machines,conduit pipe bending machine,hacksaw frame,gi pipe bending machine,pvc pipe bending spring,multi scan tool,cylinder liner,plastigauge

Air compressor for plasma cutting machine,angle plate adjustable 250 x 150 x 175,anvil 24 sq. inches working area with stand,bearing different types,boring bar indexable,caliper hermachrodite.spring 15 cm,caliper inside spring 6 inch or 15 cm,caliper outside spring 6 inch or 15 cm,caps screws m6, m8, m10, m12,carbide wear block 1 mm-2 mm.,carrier for mounting components,,drill twist 1.5 mm to 15 mm,drills guage straight shank,drills guage straight shank,cut section models for hydraulic components,cut section models for penumatic components,divider spring 6 inch or 15 cm,dowel pin straight dia. 1 inch length 4 inch,drift drill 200 mm hardened and black finish,stake grooving. 100 x 100 x 300 mm,stake hatchet with leg. 300 x 200 x 20 mm,file knife edge smooth.15o mm,file round 2nd cut 150 mm,file round 2nd cut 200 mm,file square 2nd cut 250 mm,file square rough 300 mm,file triangular 2nd cut 200 mm,marking out table 90 x 60 x 90 cm,drill gauge 1,5 to 12.5 mm in steps of 0,5 mm,drill twist st. shank metric,drill