Solid carbide drill dia: 2.85mm, fl: 66mm, oal: 100mm, shank dia: 3mm. tialn coated.

Solid carbide parallel shank twist drill

S/c drill (tialn coated) dia 13mm, fl-315 mm, oal-370mm through coolant

High performance solid carbide end mill cutter dia 12mm(sh dia 12 mm, oal 83mm, fl-26mm, bch-0.5) as

Solid carbide end mill (special) size: dia: 6 x fl: 35 x oal: 65 x 4: flute x tialn coated.

Tialn coated, solid carbide parallel shank twist drill for m achining of steel having dia. 7.5 mm, f

Sofa set,flower pot,usb charger,extension board,drill bid,carbide tip,cutting blade,flt logo paper

Spring steel handsaw,cutting pilar,wooden claw hammer,stabilizer,bosch drill machine,set bit,aluminium service cable 16mm 2 core,change over 100 amp,casing coping 20mm,grease gun 10 kg

Double end insert for external grooving and turning tgmf 404 ic830,double sided 55-degree rhombic insert dnmg 110404 - f3m ic 6025,parting insert dgn 2002c ic 808,machine reammer ts hss 32mm,machine reammer ts hss 36mm,centre drill 4mm dia type a,end mill ts hss 17 5mm dia,thread cutting tap hss m2.5 x 0.45,thread cutting die hss m2.5 x 0.45,concave mill cutter ts r13.97,concave mill cutter ts r31.75,drill twist ts hss 15.2mm dia,drill twist ts hss 16.8 mm dia,thread checking ring gauge go andno go 1by 4 inch bsw,thread checking plug gauge go and no go 1by 4 inch bsw,thread cutting tap set hss 5 16 inch bsw,thread checking plug gauge go and no go 5 by16 inch bsw,thread checking ring gauge go and no go 5 by16 inch bsw,thread cutting die set hss 5 by16 inch bsw,thread cutting tap hss 3 by 4 inch bsf 12 tpi,thread cutting die hss 3 by 4 inch bsf 12 tpi,endmill cutter ts hss 8.7mm dia,endmill cutter ts hss 11.1mm dia,endmill cutter ts hss 38mm dia,thread cutting tap set hss 1by4 inch bsf,thread checking plug gaug

Air compressor for plasma cutting machine,angle plate adjustable 250 x 150 x 175,anvil 24 sq. inches working area with stand,bearing different types,boring bar indexable,caliper hermachrodite.spring 15 cm,caliper inside spring 6 inch or 15 cm,caliper outside spring 6 inch or 15 cm,caps screws m6, m8, m10, m12,carbide wear block 1 mm-2 mm.,carrier for mounting components,,drill twist 1.5 mm to 15 mm,drills guage straight shank,drills guage straight shank,cut section models for hydraulic components,cut section models for penumatic components,divider spring 6 inch or 15 cm,dowel pin straight dia. 1 inch length 4 inch,drift drill 200 mm hardened and black finish,stake grooving. 100 x 100 x 300 mm,stake hatchet with leg. 300 x 200 x 20 mm,file knife edge smooth.15o mm,file round 2nd cut 150 mm,file round 2nd cut 200 mm,file square 2nd cut 250 mm,file square rough 300 mm,file triangular 2nd cut 200 mm,marking out table 90 x 60 x 90 cm,drill gauge 1,5 to 12.5 mm in steps of 0,5 mm,drill twist st. shank metric,drill