Procurement of m.s bolts, nuts and washers with full thread

Procurement of m.s bolts, nuts and washers with full thread

M.s rod 1200 mm long, 16 mm diameter

Reducing nipple of size 1/2 x 3/8 bsp threading (parallel) on both sides, total length - 40mm; 1/2 threaded length -15 mm; 3/8 threaded length-15mm, hex. head thickness-10mm, width af27mm, 3/8 ends inside should have tapered profile (cone type). material: carbon steel astm-a108 & grade a1018 with zinc coated. note: material should be machined from forged planks & not to be casted.

Hex head ss fasteners of size:m8 x 35mm (one set consist of one full threaded ss bolt, one ss nut, one ss spring washer & two ss flat washers). accepted offer: specification to din 933 for screw, din 934 for nut and din 125 for plain washer grade a2-70 for all.

Supply of transverse cross bond made of ms flat of size 40?6 mm, suitable for glued joints in crossover track-circuited areas, as per rdso drawing no. eti/ohe/g/05251, with holes at both ends and complete with gi bolts of size 16?50?38 mm along with nuts, spring washers and flat washers; and cross/transverse bond and special bond fabricated from ms (mild steel), complete with ms flats duly painted with one coat of red oxide primer and finished with black paint, suitable for ohe bonding and ret

Alkaline battery 9v,copper binding wire 0.5 mm diameter,copper wire bare 8 swg or 4 mm dia.,crocodile pin set,current selective switch 16a,elcb 25a 2 pole,electrical sequential control circuit 4 channel,g.i. sheet plain 22 swg or 0.64 mm thickness 1200 x 2500 mm,g.i. sheet plain 24 swg or 0.55 mm thickness 1200 x 2500 mm,g.i. sheet plain 26 swg or 0.45 mm thickness 1200 x 2500 mm,grinding wheel coarse for pedestal grinder,hpsv ignitor 150w,hpsv lamp holder 150 w,hydrometer for battery testing,intermediate switch,led 5 mm 3v blue,led 5 mm 3v green,led 5 mm 3v red,led 5 mm 3v yellow,led lamp holder with cap,li charging cell 2000 mah,m.s. angle 35 x 35 x 05 mm,m.s. pipe 01 inch or 25 mm dia. 2.5 mm thickness,m.s. pipe 01.5 inch or 38 mm dia 3.5 mm thickness,m.s. round bar dia 10 mm,m.s. square bar 25 x 25 mm,m.s. wire dia. 04 mm,male female 5a,push button switch on off,plywood laminated sheet 200 x 150 x 03 mm,remote control switching system 4 module,rg - 6 cable connector,rj 45 cable connector,sanmaica wooden b

Set of nipples required for pneumatic pipelines consisting of two items as follows. 1) 1/2 x 1/2 nipples both sides parallel threads as per drg. no. b/trs/pn.eqpt/3/56 or latest. qty/set. = 03nos. 2) 3/4 x 1/2 reducing nipple taper & parallel thread(nom dimension in mm on od: 27 x 21r & nom diameter in mm on id: 20.15 as per drg. no. b/trs/pn.eqpt/3/18, alt a or latest if any. qty/set. = 01no. note: ten sample sets should be got approved before effecting bulk supply.

Set of two legged 32 mm steel wire rope sling, with master o ring, double crimped with thimbles on both sides as per is2762 : 2009 according to ryps drawing ryps/scr/j&t/sk-1013. make : for master o ring : yoke or crossby or isi marked or equivalent as per is2760 : 2009. make : for 32 mm wire rope : usha martin or bharat or wire co old group usa or bekaert belgium or equivalent as per is2266 /2002 .

For complete deion and other details, please refer to tender