Window cover /inspection cover for bhel hhp tm type 4303by conforming to bhel drg no.-24393141003 or balaji enterprises drawing no. be/demu/ tm/wc20-26 .note-1)company name and p.o. no.should be embossed on component,2)material to be supplied with anti corrosion coating. 3.) the sample piece should be got approved by the consignee before bulk supply.

Wire wound resistor 4.7 ohms 1000w, size 50 mm outer dia and resistor length 380 mm with suitable fixing clamp item to be supplied along with fixing clamps. height of fixing clamp should beabove 35 mm.

Trochanteric femur nail advanced system one set. spec: (1) 9 mm to 12 mm diameter with inbuilt set screw. (2) should be capable of allowing cannulated screw or blade (one) with same hole in proximal part. (3) end of blade and screw should be porous to allow augmentation with 5 mm distal locking option (two). (4) material should be titanium molybdenum. (complete range of size shape and side specific implant with instrumentation should be available at the time of surgery).[ item code no.:s6155

Piston screw,for csm, duo & mfi machines [piston screw,for csm, duo & mfi machines. equivalent to plasser part no.: 2e36.48 as per rdso drawing no.: tm/0426 and rdso specification no.: tm/hm/6/162, part make: plasser or equivalent, note: material supplied by firm should be fitted on machine without any modifications and all ports & mounting should match as per existing part on machine and all function of item should work successfully. ]

Insulating rod assembly for positive & negative support insulator for hitachi tm type hs-15250a to drg.no. skel-4439, alt-1, ref: 1 to 4. note: one sample set should be got approved before effecting bulk supply. (as per uvam id:2101199).

Supply of managaed expandable rack type stm-1 adm l-1-1 as per technical specification no tec gr no-gr /tx/sdh/004/04 jan 2011 (tec 86020:2011) with stm-1 aggregate interface 32 e1s & 4 nos of 10/100 base t ethernet port, order wire, power supply unit sub rack installation material & accessories manual & software etc. the equipment should be fully wired for its ultimate capacity.the equipment should be fully compatible/interpretable with existing stm-1 network (tejas-tj1400).

Supply of contact wire parallel clamp (small) part no. 1041-2 complete with fasteners as per rdsos spec. no. ti / spc / ohe / fittings/0130- (10/13) rev-1 and rdsos drawing no. eti/ohe/p/1040-2 reve or latest. material must be procured from core/rdso approved vendors or their authorised representatives. the authorization letter from core/rdso approved vendor, submitted with the offer should be tender specific. (drawing attached)

Main base frame,base longitudinal member,base cross member,main vertical support,vertical side support plates,hydraulic cylinder,hydraulic cylinder body,hydraulic ram capacity,hydraulic pump,pump operating lever,main pulling arm,pulling arm pivot pin,secondary link,connecting link,pulling chain,chain connection shackle,holding hook,main equipment cradle,cradle base plate,cradle side plate,adjustable clamp,main locking pin,secondary locking pin,adjustable screw,adjustable hand wheels,main transport wheels,support wheel,main wheel axle,support wheel axle,ou arm,stabilizer vertical post,stabilizer foot,stabilizer operating handle,hydraulic hose,hydraulic pipe,structural gusplates,main load bearing plates,general brackets,pivot bush,safety retaining pins,fasteners

Va fibula plate (1 plate + 8 va locking screws + 6 cortical screws). spec: locking anatomical five hole variable angle distal fibula plate with 8(2.7 mm) va screw for head and shaft with two 3.5 cortical screw option in head for syndesmotic layer and 4(2.7mm) cortical screw, variable angle locking screw should have option to lock at + - 15 degree of axis in any direction complete range of size shape and side specific implant with instrumentation at the time of surgery. implant should be us fda

Resistance 4.7 ohms,1000 watt as per drawing no. mei/w- wres/26122017-12 with inverted clamp height of 100 mm and suitable for fixing in existing panel board of size 400 x 250 mm as per clw specification no.clw/es/c-47/1 suitable for rc damping panel for auxiliary winding for transformer. the material must be of following make ; escol, vepl, pec, sur , kiyosh or equivalent manufacturers name and manufacturing month & year should be clearly mentioned on material.