Supply installation of solar high mast light of 4x18 watt (10no.) with li-ion phosphate battery.

Gps,power module,esc,propellor,control rods,servo motors,servo motors attachment,fc fixhawk 2 4 8,micro camera,carbon rods,c rtk,gps antena,battary lipo 2400 mah,folding propellor,li ion battery 10000mah,drone rubber damper

Gps,power module,esc,propellor,control rods,servo motors,servo motors attachment,fc fixhawk 2 4 8,micro camera,carbon rods,c rtk,gps antena,battary lipo 2400 mah,folding propellor,li ion battery 10000mah,drone rubber damper

Nibp hand cuff set,spo2 probe,ecg cable 5 lead,bull nose fitting,ecg cable 10 lead,alcohol isopropyl technical,li ion bty 7 2v 4400mah,paper sensor,thermol roller,x ray viewer 36 watt cfl tube

Frame,brush less motors,thirteen inch propeller tri blade,flight controller,esc,fpv camera,dual gps module,battery pack,optical fiber spool ten km length,optical fiber air unit,ground unit,express lrs dual band receiver,fpv google with antenna,radio controller,spare li ion cells,hard case,safety mechanism and detonation for kamikaze load,payload holder,allied accessories connectors cables,user manual,log book,additional equipment,spare bty,of propellers,storage box for bty

Supply of 5 watt vhf set batteries for digital motorola xir p6600i (li ion 7.4 volts/2450mah) as per specification no. rdso/spn/tc/107/2018 or latest. battery shall be of radio oem and bis approved as is 16046 / iec 62133.

Mark iv carbon fiber frame,bonka 22 point 2v 5200 mah 35c 6s lithium bty,i max eco 2807 1300kv bls motors,propellers,stack micoair,geprc mataen vtx pro,foxeer pagoda pro omini fpv antenna,radio master rp3 elrs receiver,radio master gx12,micoair m10 gps ultra,camera run cam phoeonix 2,capacitor 35v 1000 micro fared,dc buck converter,li ion,goggles sky zone sky 40 pro,xt 60 connector,bty anti slip pad,antennas,foxeer pagoda pro 5 point 7 ghz

Supply and configuration of digital trans-receiver handheld 5 watt vhf set conforming to clause 5a or 5b of rdso specification no. rdso/spn/tc/107/2018 ver, 2.0 or later, along with two set of oem approved rechargeable batteries including one as spare, additional requirements: 1) spot frequency - 159.650 mhz & 160.400 mhz. 2) battery type -ni mh or li-ion. 3) battery capacity - minimum 2300 mah and should work for at least 10 hours. 4) two numbers of tuning kit with software to program shall b

Ammeter 300a by 60a dc with external shunt,auto transformer 15 amps,automatic reverse forward starter,bradawl 150 mm x 6mm square pointed,cable joining clamp,capacitors electrolytic ceramic polyester film variable dual run,coil winding machine manual,conduit pipe bending machine,conduit pipe cutting and threading machines,philips screw driver set of 5 pieces 100mm to 300mm,plier side cutting 200 mm,contactor 3 phase,440 volt,16 a with nc auxiliary contacts,control panel 5 x 3 x 1.55 x 3 x 1.5 feet,crimping tool pliers 7 in 1,crimping tool for crimping 16 sq mm to 95 sq.mm,cut out relays,digital lux meter lcd read out 0.05 to 7000 lumens with battery.,earth electrode secondary cu strip 20x5mm,earth gi plate 60cm x 60cm x 6mm,flux meter,foot print grip 250 mm,knife double bladed electrician 100 mm,knife switch dpdt fitted with fuse terminals 16 amp,knife switch tpdt fitted with fuse terminals 16 amp,lamp cfl 5 watt, 15 watt, 25 watt set,meter reading instrument mri,omx controller,panel accessories cable ducts,